Kopplingsplint 2.5 mm2 12-polig

Reference: 02-037

Brand: Energibutiken, WebIQ AB

Compression fitting 1/4"

Compression fitting 1/4" Smooth compression fittings for mounting our temperature probes with 6 mm protective cover (see picture). This compression fitting allows you to, via a a T-pipe coupling, plug in your temp sensor directly in the flow of the media you are measuring the temperature of.

Reference: 04-010

Brand: Energibutiken, WebIQ AB

Heat conductive paste 3 ml

Heat conductive paste 3 ml This paste is great to use when installing a temp sensor to pipes, tanks or in temp pockets. A small amount of paste is enough to improve the measurement accuracy, particularly in terms of reaction times during sudden temperature changes.

Reference: 04-008

Brand: Energibutiken, WebIQ AB

Junction Box

Junction Box Junction box, with five-pole terminal block. To connect the temperature sensors and electricity sensors cables to Logger 2020.

Reference: 04-012

Brand: Energibutiken, WebIQ AB

Cable 2X0.14 mm2

Cable 2X0.14 mm2 Unshielded cable for connection of electricity meter sensors, digital input sensors.Area: 2 x 0.14 mm2Color: Gray Select cable length before adding to cart.

Reference: 04-005

Brand: Energibutiken, WebIQ AB

Electricity meter sensor

Electricity meter sensor Sensor reads flashing from IR or UV diodes, particularly for use with the Logger 2020. Simply attach these sensor via 2-lead wire to Logger 2020:s E1 or E2 terminals in order to monitor energy and power consumtion.

Reference: 04-023

Heat conductive paste 20 grams

Heat conductive paste 20 grams This paste is great to use when installing a temp sensor to pipes, tanks or in temp pockets. A small amount of paste is enough to improve the measurement accuracy, particularly in terms of reaction times during sudden temperature changes.

Reference: 04-004

Brand: Energibutiken, WebIQ AB

Electricity meter sensor, encapsulated

Electricity meter sensor Sensor reads the flashing of IR or UV diodes, particularly for use with Logger 2020 and SunLogger 2020 monitoring units. The sensor is easily connected with a two-core cable to the Logger 2020 or SunLogger 2020 input terminals E1 and/or E2.

Reference: 02-035

Brand: Energibutiken, WebIQ AB

Temp pocket stainless steel 1/2"

Temp pocket in stainless steel 1/2 ". Temp pocket in stainless steel. Temp pocket suitable for e.g. solar panels or in installations where a certain mechanical wear can occur. The actual temp pocket in contact with the media is AISI 316Ti and the "head" is in AISI 303 Fits our temperature sensors with 6 mm protective sleeve over the temperature sensor.

Reference: 04-009

Brand: Energibutiken, WebIQ AB

Analog Light sensor 0-5 V

Light sensor Three-wire lightning to voltage converter, the sensor are adapted to the Logger 2020's A/DMIQ I/O-module, and can be used both as analog sensor to the analog inputs, and for indicatiing status of measured diods/lamps indication service status  - on the digital inputs of the A/DMIQ -module.

Reference: 04-022

Heat conductive paste 3 grams

Heat conductive paste 3 grams This paste is great to use when installing a temp sensor to pipes, tanks or in temp pockets. A small amount of paste is enough to improve the measurement accuracy, particularly in terms of reaction times during sudden temperature changes.

Reference: 04-013

Brand: Energibutiken, WebIQ AB

Cable 3-wire

Cable 3-wire Unshielded cable for connection of temp sensors/modules and/or to use as a bus conductor in the system. Area: 3 x 0.14 mm2Color: GraySelect cable length before you add to shopping cart.

Reference: 04-011

Brand: Energibutiken, WebIQ AB

Ethernet cable

Ethernet cable Unshielded cabling consisting of a 4-pair cable, Category 5e (Cat 5e), and an RJ45 connector on both ends. This cable are needed to connect Logger 2020 to your router if you want to run your Logger 2020 against the web service e-logger.se - or if you need to update the software in your Logger 2020.Select cable length before adding to cart.

Reference: 02-036

Brand: Energibutiken, WebIQ AB

Compression fitting for temp sensors

Compression fitting for temp sensors Smooth compression fittings for mounting temperature probes with 6 mm sleeve (see picture). This compression fitting allows you, via a T-pipe coupling, to plug in your temp sensor directly in the flow of the liquid you are measuring the temperature of.

Reference: 04-014

Kopplingsplint 2.5 mm2 12-polig

Terminal block 2.5 mm2 12-pin With cable protection, made of nylon.

Reference: 03-013

Power supply 12V, 1.25A, 15W HDR-15-12

Power supply 12V, 1.25A, 15W H Switched power supply 12V 1.25A 15W for DIN rail. The unit has adjustable output voltage 11V to 13V and handels voltage 100V to 240V. The unit has a working temperature of -30°C to + 70°C. This type of power supply has a low idle consumption.

Reference: 02-034

Brand: Energibutiken, WebIQ AB

Temp sensor pocket 1/2"

Temp sensor pocket of chrome-plated brass. Temp pocket suitable for such solar heating systems or in facilities where mechanical damage may occur. Fits our temp sensor with 6 mm protective sleeve over the temp sensor.